Category: Wireless Lens Control
Weight:
Motor Dimensions:
Color: Gunmetal grey
Material: Aluminum-alloy, stainless steel, ABS plastic, rubber, Brazilian rosewood
Category: Wireless Lens Control
Weight of hand unit: 707 g (including battery and marker ring)
Weight of camin: 156 g
Weight of motors: cforce plus: 326 g (including clamp); cforce mini: 173 g (including clamp)
Wireless frequency: 2.4 Ghz
Wireless range: up to 30m (100 feet) indoors, 200m (600 feet) outdoors
Wireless channels: 8 channels
Environmental requirements: from -20° to 50° C (-4! to 122° F)
Operational hand unit hours with fully charged battery: up to 8 hours
Transmission delay: <10ms
Software update via USB port: Yes
Maximum axis control: 3 motors
Motor compatibility: cforce basic, cforce mini, cforce plus
Hardwired operation possible: Yes (connect directly to cforce motor via LBUS cable)
Same function for left and right handed operators: Yes
Independent wireless control units per camin: 1
Display on hand unit: 2.3″” color TFT
Start/Stop function: ARRI, Sony, Red, Canon, Black Magic, Broadcast cameras (via 12p Hirose)
Shows focus , zoom, iris position: Yes
Shows lens data: Yes (cworld required to create lens data. Saves up to 14 lenses on hand unit)
Range finder compatibility: Yes (for cfinder III through LBUS connector of the cforce daisy-chain. For UDM, Cinetape, Through ARRI LCUBE). cdistance is required for range finder read out
Autofocus function: No
Set direction, torque and ramp of motor: Yes
Set digital lens limits: Yes
Shows battery and connection status: Yes
Color themes for optimized display read out: 5 color themes
Compatibility to other products: cdistance, cfinder III, knob solo, pan-bar zoom, steady zoom, UDM (via LCUBE)
Automatic motor calibration: Yes
Manual motor calibration (for lenses without hard stops): Yes
Save settings via USB: Yes
Category: Wireless Lens Control
Description
The Bartech Focus Device is a single-channel wireless lens control system, compatible with existing analogmotors (Heden, ZB/SLD, FMG-6, as well as the M-One motor); motor sold separately.
Key Highlights
Single-Channel Lens Control System
900 MHz Data Transmission
(8) Selectable Sub-channels
Category: Wireless Lens Control
The Preston Digital Micro Force zoom control is available in two versions; the V+F3 control for analog motors and the Digital Micro Force2 for digital motors. Both models provide the smooth flawless zooms that have made them the favorite of camera assistants worldwide. Either control can provide the zoom command signal for the FI+Z system as well as drive the internal motors of most Video lenses. A bright digital display shows the speed setting and the maximum speed is set with a new rugged encoder.
Zoom speed is controlled by applying thumb pressure to the joystick. The rugged Micro Force sensors give the operator precise tactile feedback for fine control.
The Digital Micro Force2 drives the DM-1X andDM-2 digital motors. It automatically calibrates the motors to the mechanical span of the lens, preventing accidental damage to either the lens or motor. A bright LED bargraph displays the zoom position. Electronic limit stops can be set with the touch of a button.
The soft stop feature allows the user to automatically slow the zoom a programmed distance from its end of travel. This is especially useful when doing a fast “snap” zoom, or when the user must both operate the camera and control the zoom at the same time.
The V+F3 control can drive a wide variety of analog zoom motors including the Heden M26T motors as well as the integral Panavision zoom motors.
The Articulating Pan Arm Adapter attaches the Micro Force zoom control to either an 18mm or 3/4″ pan arm.
A wide variety of accessories are available for interfacing the Micro Force to either film or video cameras and lenses.
